![]() It's a linksys WRT54GS version 5 with DD-WRT v23 SP2 (09/15/06) micro. I tried to reset it to factory settings too but it did not work too. The firewallbuilder basiclly creats and installs a firewall script that the firmware can understand so try using it. I am using Linksys with the std version 23-SP2 and it works perfectly with no problem at all, so it should work.Īnd by the way i do think you can use firewallbuilder with the micro version. (maximum ports should be 4096 and timeout of a 120 seconds for both TCP and UDP), and the right port forwarding rules.īy the way which router and firmware version are you using? If the above does not work try changing to a different version of DD-WRT. Make sure to configure the right values in the router’s IP Filter Settings which is under administration – management tab. Try resetting the router to factory default under the administration – factory defaults tab and try to reconfigure your router again. I already tried to hard reset the router again but this time it did not work. If I connect my cable modem directly to my computer I have no problem on people connecting to me, but if the router (which is correctly configured) is in the middle people can't connect to me. Not sure what is the problem, it seems that there is a bug on the firmware. Then I reconfigured and the forwarding started to work again, but 2 days after the reset is stopped again. Previous week I had problem with my router so I hard reseted it. but it simply stop working a few days after I installed DD-WRT It is not working, I have the correct ports and ip set, the rules are enabled. If im right about that u just need to go to application and gaming tab and then use the port forwarding tab to forward the ports to your computer So i guess you are using the regular firewall. "Furthermore there is an explanation in the DD-WRT wiki about how to create the NAT port forwarding rules trough the command line of the router, however the GUI way is a little easier to work with. Not sure if I can use use firewall builder on this case. ![]() In the link I posted there is an example how to configure the NAT. I'm having the same problem here, could you be a little clear about the solution you found?īasically if you are using the firewall builder software u just need to open the ports you need on the policy tab in the software GUI.Īfter you opened the ports you need to allow them on the NAT tab. The solution applies to any port you want to forward not just for emule. ![]() Here is a link that explains in details how to create the NAT rules trough the Firewall Builder GUIįurthermore there is an explanation in the DD-WRT wiki about how to create the NAT port forwarding rules trough the command line of the router, however the GUI way is a little easier to work with. So in order to solve this problem there is a need to configure to correct NAT rules in order to make the firewall forward the request to the right host. I would appreciate if someone can tell me what is wrong with my configuration, and what I should do to correct this problem.ĭo you use Windows XP's firewall or some software firewall? Make sure they allow eMule to connect to internet.Īfter a bit of reading and looking in the wrong places I found out that when using firewall builder to create a base rule for the router the script that the software creates ignores the setting in the Application and gaming - port forwarding section. So obviously something is wrong with firewall configuration. When I try to connect emule with the original firewall rules (the one that came with the firmware and not the one done by the firewall builder) it does connect. So because of that I can’t get emule to connect. From the syslog messages the firewall does let the port request in but there is no forwarding done. However for some reason the firewall does not forward those ports. 4662 TCP and 4672 UDP).Īnd port forwarding is enabled to forward these ports into a specific computer in the LAN. I also have the right ports opened on the firewall (i.e. I have the QOS functions enabled and IP Filter Settings set to maximum ports of 4096 and timeout of 120 for both UDP and TCP. I am using a v.23 SP2 and firewall builder to configure the routers firewall, and I have problem connecting emule. I hope someone can help me with this problem Posted: Sun 19:57 Post subject: DD-WRT Firewall, Emule failing to connect
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |